LAUNCH CR3008 PLUS OBD2 Scanner Engine Battery Diagnostic Tools Auto Code Reader Scan Lifetime Free Update Online

LAUNCH CR3008 PLUS OBD2 Scanner OBDII Code Reader Tool for Check Engine Light battery Voltage Test

LAUNCH CR3008 PLUS Language :

Portuguese, German, Japanese, Russian, Spanish, English and French

LAUNCH CR3008 obd2 code scanner can read and erase codes which can also retrieve a wealth of information from the Engine Control Unit (ECU). The ECU is what triggers the Check Engine Light when there is a problem with your car. Parts might cause your check engine light on include:

#1. Gas Cap #2. Oxygen Sensor #3. Air Fuel Ratio Sensor #4. Mass Air Flow Sensor #5. Ignition Coils #6. Spark Plug Wires #7. Spark Plugs #8. Thermostat #9. EGR Valve #10. Evaporatative Emission Canister Purge Valve(EVAP) #11. Catalytic Converter.

And LAUNCH CR3008 obdii code reader will read codes indicating these fault parts. After the car problems have been solved, LAUNCH CR3008 car code reader can erase these trouble codes and turn off check engine light.

Full OBD2 Check--Make a Better Detection for Car Engine System!

This scanner supports all 10 test modes for OBD-II cars which are great for daily repair work. The table below describes the purpose of each mode of operation:

1. Reading Codes: Show the detailed description of the Diagnostic Trouble Code (DTCs)

2. Erasing Codes & Reset: Turns off Check Engine Light (MIL), clears codes and resets monitors.

3. Data Stream: Reads and displays live ECU/PCM data stream, plotting functions graphically and stores freeze frame data.

4. I/M Readiness Status: Shows whether the various emissions-related systems on the vehicle are operating properly and are ready for inspection and maintenance testing.

5. Read Live Data Stream: Show the information of continuous data stream from a vehicle in live graphic (waveform) display.

6. View Freeze Frame Data: Check the certain vehicle conditions which are recorded by the on-board computer at the time the emission-related fault occurs.

7. O2 Sensor Test: Allows retrieval and viewing of O2 sensor monitor test results for the most recently performed tests from the vehicle’s on-board computer.

8. On-Board Monitor Test: Retrieves and displays test results for emission-related powertrain components and systems.

9. Read Vehicle Information: Display the information such as VIN (Vehicle Identification Number), CID (Calibration ID) and CVN (Calibration verification number), etc.

10. Component Test: Certain vehicle components can be actuated by commands sent from the scanner to test their operability.

LAUNCH CR3008 ODB2 Car Diagnostics Support vehicles

LAUNCH CR3008 supports both 12V diesel and gasoline vehicles, as long as the car is compliant with standard OBDII/EOBD protocols, with OBDII 16pins diagnostic port.

American (USA) cars

for Standard OBD2 Cars from 1996 to Now:
for Chrysler, for Ford, for GM, for Jeep

European cars

for Standard OBD2 Cars from 2003 to Now:
for Alfa Romeo , for SAAB , for Acura , for Opel, for Audi , for Seat , for Bentley , for Skoda , for Daewoo, for Benz , for Daihatsu , for Land Rover, for BMW , for Vauxhall ,for Volvo ,for VW , for Ford , for Jaguar

Japanese cars

for Standard OBD2 Cars from 2008 to Now:
for KIA, for Isuzu, for Honda , for Mitsubishi, for Hyundai , for Dacia , for Lexus , for Mazda, for Nissan, for Subaru , for Suzuki, for Toyota.

Chinese cars:

for Standard OBD2 Cars from 2014 to Now:for BYD, for Chery, for Geely, for Great Wall, for Karry

LAUNCH CR3008 PLUS supports Lifetime Free Update via PC , 5 Years warranty , Lifetime Tech Support !!!

LAUNCH CR3008 Plus Packing List :

1pc LAUNCH CR3008 Plus Main Unit
1pc Manual book